System startup
version:U-Boot 2018.07 (Dec 03 2020 - 16:48:04 +0800)

TLB ADDR:0xe000000
Build Date:    Dec  3 2020, 16:48:40
CPU:           Hi3751v350
Boot Media:    eMMC

gd:10bfff50,DRAM addr:0x0,size:0x40000000
1 GiB
WARNING: Caches not enabled
board_init,41
MMC:   hisi-sdhci: 0

EMMC/MMC/SD controller initialization.
current clock: 400000Hz, host timing: 0x0
current clock: 52000000Hz, host timing: 0x1
current clock: 120000000Hz, host timing: 0xa
MMC/SD Card:
    MID:         0x15
    Read Block:  512 Bytes
    Write Block: 512 Bytes
    Chip Size:   7456M Bytes (High Capacity)
    Name:        "8GTF4"
    Chip Type:   MMC
    Version:     5.1
    Speed:       120000000Hz
    Bus Width:   8bit
    Mode:        HS400ES
Loading Environment from MMC... OK
Net:

Slave boot startup

version:U-Boot 2018.07 (Dec 03 2020 - 16:57:47 +0800)

TLB ADDR:0x10e00000
Build Date:    Dec  3 2020, 16:58:11
CPU:           Hi3751v350
Boot Media:    eMMC

gd:13ffff50,DRAM addr:0x0,size:0x40000000
1 GiB
WARNING: Caches not enabled
board_init,41

The DDR memory layout:
      page table: 0x10e00000 - 0x11200000  4 MiB
           stack: 0x11200000 - 0x11600000  4 MiB
       irq stack: 0x11eefecc - 0x11fefecc  1 MiB
           .text: 0x14000000 - 0x14069674  421.6 KiB
            data: 0x14069674 - 0x160f9848  32.6 MiB
init_sequence_r done!
Not enough memory for reserve memory!
fastboot#  <INTERRUPT>
fastboot# <INTERRUPT>
fastboot# <INTERRUPT>
fastboot# <INTERRUPT>
fastboot# <INTERRUPT>
fastboot# cant has HI_DRV_MAILBOX_CVTE_UPGRADE_INFO
Loading Environment from MAILBOX... OK
<INTERRUPT>
fastboot# <INTERRUPT>
fastboot#

fastboot# help
?       - alias for 'help'
base    - print or set address offset
bdinfo  - print Board Info structure
bootatf - boot atf ,kernel and secureos from memory
bootatf32- boot atf ,kernel[32bit] and secureos from memory
bootp   - boot image via network using BOOTP/TFTP protocol
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
cvt_usb_init-  init cvte boot usb file list
ddr     - ddr training function
editenv - edit environment variable
env     - environment handling commands
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fatsize - determine a file's size
fatwrite- write file into a dos filesystem
getinfo - print hardware information
go      - start application at address 'addr'
gzwrite - unzip and write memory to block device
help    - print command description/usage
i2c_read- I2C Read, please be careful !!!
i2c_write- I2C Write, please be careful !!!
loadb   - load binary file over serial line (kermit mode)
loadsos - load secure os at address <addr>
loadx   - load binary file over serial line (xmodem mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcinfo - display MMC info
mw      - memory write (fill)
nm      - memory modify (constant address)
otpreadall- read otp ,for example otpreadall
otpwrite- write otp ,for example otpwrite adddress value
ping    - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sleep   - delay execution for some time
standby - test standby
start_slaveboot- slaveboot debug
tftp    - tftp  - download or upload image via network using TFTP protocol
tftpboot- boot image via network using TFTP protocol
tftpput - TFTP put command, for uploading files to a server
timershow- timer_show start
unzip   - unzip a memory region
usb     - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version

?       - alias for 'help'
CmdPerformanceTest- gettime   - Get the system executing time

ac      - set a new config to the bootargs

aesdma  - aesdma - do the aesdma command.

audio_preinit- audio_preinit   - Init audio driver

auto_flash- do auto flash image.

auto_tftp- do auto-address tftp.

base    - print or set address offset
bdinfo  - print Board Info structure
bin2emmc- bin2emmc - read bin file and restore it to emmc

boot    - boot default, i.e., run 'bootcmd'
bootargs_set- Set info exchange and set to boot args.
bootcheck- bootcheck   - Do boot check

bootd   - boot default, i.e., run 'bootcmd'
bootlogo- bootlogo   - Display Logo_Music

bootm   - boot application image from memory
bootmusic- bootmusic   - play music

bootp   - boot image via network using BOOTP/TFTP protocol
checkUsbModeSwitch- checkUsbModeSwitch  -

checkVersion- check current verison and upgrade image version

checkfile- check file exist in u disk,and set the partition.
checkstr- check_str_resume

checktee- Check TEE binary
chkmiusetting- chkmiusetting   - Check MIU setting

cleanallenv- cleanall environment variables to persistent storage
cmp     - memory compare
cnstar  - do net update from the specified file that is in oad partition

config2env- Set config to environment.
config_raw_io- Config the target device for raw I/O
coninfo - print console devices and information
costar  - do oad update from the specified file that is in oad partition

cp      - memory copy
crc32   - checksum calculation
createMbootBak- emmc create mbootbak partition -

ctv_factory_mode_check- factory mode to check usb files and do test

custar  - do usb update from the specified file that is in usb.

dbg     - set debug message level. Default level is INFO
dbtable_init- dbtable_init   - let data  is ready (logo, music, panel, ursa).

dc      - delete the specific cofig that is in the bootargs

delay   - delay time, time unit is ms

destroy_logo- destroy_logo - Stop logo display

dhcp    - boot image via network using DHCP/TFTP protocol
dont_overwrite- This serial apis are for protecting the specific partitions are                                                                              overwrited. ex: customer
This cmd is used to register which partition should not be overwrite

dont_overwrite_free- This serial apis are for protecting the specific partitions                                                                              are overwrited. ex: customer
This cmd is used to free all registered partitions.

dont_overwrite_init- This serial apis are for protecting the specific partitions                                                                              are overwrited. ex: customer
This cmd is used to init this function

dont_overwrite_switch- This serial apis are for force write and re-create partit                                                                             ions.
This cmd is used to disable dont_overwrite function.

draw_jpg- blt_jpg   - Blt JPG

draw_pixel- draw_pixel - draw a pixel with color

draw_progress- draw_string - draw string with color

draw_rect- draw_rect - draw rect with color

draw_string- draw_string - draw string with color

du      - du  - Disable UART

ebist   - PHY loopback test
echo    - echo args to console
editenv - edit environment variable
edump   - EMAC Register settings dump
eloopback- Long loopback test
emmc    - eMMC sub system
emmcbin - emmcbin - dump emmc and restore it to fat usb disk

emmcbootbin- emmcbootbin - dump emmc boot partition and write it to fat usb disk

env     - environment handling commands
envload - envload   - reload the nand environment.

epd     - emac power down
estart  - EMAC start
ewavetest- EMAC wave test
exit    - exit script
ext2load- load binary file from a Ext2 filesystem
ext2ls  - list files in a directory (default /)
ext4filesize- get file size from a Ext4 filesystem
ext4load- load binary file from a Ext4 filesystem
ext4ls  - list files in a directory (default /)
ext4partload- part load binary file from a Ext4 filesystem
ext4write- create a file in the root directory
factory_check_usb_files- check usb files, enter diffrrent mode

false   - do nothing, unsuccessfully
fastboot- enter fastboot mode
fatfilesize- fatfilesize - load binary file from a dos filesystem

fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls   - list files in a directory (default /)
fatpartload- fatpartload - load binary file from a dos filesystem

fatwrite- fatwrite - write binary file to a dos filesystem

filelist- Dump the file list.

filelisttest- This command is only for file list test

filepartload- load part of a file to RAM
filepartloadSeg- load a seg part of file to RAM
flashbin- flashbin - dump/restore emmc or nand flash data to/from flash.bin

force_overwrite- This serial apis are for force write and re-create partitions.
This cmd is used to register which partition should force overwrite

force_overwrite_init- This serial apis are for force write and re-create partiti                                                                             ons.
This cmd is used to register which partition should force overwrite

get_mmap- get memory info from supernova's mmap
gettime - gettime   - Get the system executing time

go      - start application at address 'addr'
gpio    - GPIO Command:
help    - print command description/usage
i2c     - I2C sub-system
if_boot_to_pm- if boot to PM

iminfo  - print header information for application image
imxtract- extract a part of a multi-image
initDbgLevel- Initial varaible 'dbgLevel'
init_raw_io- init raw_io module
ir_delay- ir_delay   -  delay 300ms for IR detect.

itest   - return true/false on integer compare
kernelProtect- kernelProtect  - Protect kernel

kernelProtectBist- kernelProtectBist  - Protect kernel bist

led     - See led commands
loadb   - load binary file over serial line (kermit mode)
loadenv - loadenv   - load env for nand

loads   - load S-Record file over serial line
loadspi - load data from SPI
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
lz4     - LZ4 decompress
m2e     - Restore the address and len to env from supernova's mmap

macaddr - setup EMAC MAC addr
mbootver_set- setmbootver   -  for customer show in factory menu.

mbup    - mboot upgrade

md      - memory display
memtest - Get the performance of memory
miuProtect- miuProtect  - Protect miu

mm      - memory modify (auto-incrementing address)
mmc     - MMC sub system
mmcbininfo- mmcbininfo - Valid block num in each partition

mmcinfo - display MMC info
mmcreg  - mmcreg show ext-csd
modelinfo- modelinfo   - check model info if need sync to sync dbpool

mscompress7- Compress or decompress lzma files
msg     - print string - msg [string]

mstar   - update kernal & root file system automatically by script file
mstar_usb- MStar USB Driver Porting
mtest   - simple RAM read/write test
multi2optee- For Multi Optee Image writting to EMMC
mversion- show changelist - mversion

mw      - memory write (fill)
nm      - memory modify (constant address)
nstar   - nstar   - update softwave system automatically via net

nuttxProtect- nuttx Protect  - Protect nuttx

osd_create- osd_create - create osd layer

osd_destroy- osd_destroy - destroy osd layer

osd_flush- osd_flush - flush canvas to screen

ostar   - ostar   - update softwave system automatically via oad

ota_zip_check- do OTA zip package check.

panel_init- panel_init  - init panel by panel.ini

panel_post_init- backligth on  - backlight on

panel_pre_init- panel_pre_init  - init panel by panel.ini

ping    - send ICMP ECHO_REQUEST to network host
pm51    - pm51 command: pm51 [option]

pmProtect- runtime pm Protect  - Protect runtime PM

pop_raw_io_config- pop raw_io last config
printenv- print environment variables
push_raw_io_config- push raw_io current config
qhb_check- run QHB flag check
raw_io_status- get raw_io status
raw_read- Read the raw datas that store in the target device
Yo have to execute 'config_raw_io' before using this cmd

raw_write- Write the raw datas that store in the target deviceYo have to execute                                                                              'config_raw_io' before using this cmd

readArmFw- readArmFw   - read Nuttx to malloc buffer

readOptee- readOptee   - core1 run at Nuttx

recovery_wipe_partition- do recovery wipe data or cache.

reset   - Perform RESET of the CPU
riu     - riu  - riu command

run     - run commands in an environment variable
runtime_pm- if boot to PM

sar     - sar Command:
saveenv - save environment variables to persistent storage
setenv  - set environment variables
showboard- Show board information
showtb  - Show register command table.    -  showtb [stage]

showvar - print local hushshell variables
showversion- Show version
sleep   - delay execution for some time
smc     - smc   - jump to arm_trusted_firmware

source  - run script from memory
sparse_write- do sparse image writing to target flash type.

spi2usb - Read data from spi to usb
sync_mmap- Sync the some id's address and len to env and bootargs from supernova                                                                             's mmap

test    - minimal test like /bin/sh
testmode- set testmode into bootargs.
tftpboot- boot image via network using TFTP protocol
true    - do nothing, successfully
udstar  - Execute the script file that is stored in usb disk

unlockcmi- unlock cmi transfer board   -  unlock

update_mode- get/set update_mode

updatemiureg- Call driver to update miu setting
usb     - USB sub-system
usb2spi - write data from usb to spi
usb_bin_check- do usb bin document check.

usb_partial_upgrade_to_emmc- partial upgrade from USB to eMMC

usbboot - boot from USB device
ustar   - ustar   - update kernal & root file system automatically by script fil                                                                             e

version - print monitor, compiler and linker version
wdt_enable- wdt_enable n - set Watchdog timer to n secs
 

AC_ON
BIST0-OK
BIST1-OK
_U
Relocation Offset is: 01200000
[AT][MB][start ub][553]

U-Boot 2011.06-00014-g71b92a5-dirty (Jun 20 2018 - 13:51:19)  MBOT-1106.0.10.1340012

DRAM_SIZE1=512 MB    DRAM_SIZE2=512 MB    DRAM_SIZE3= MB
msIR_Initialize
[SYS][Utopia]: Function = SYSOpen, Line = 815, current resource pri_shm content is: 0
[SYS][Utopia]: Function = SYSOpen, Line = 834, [SYS INFO] OPEN INSTANCE...
create instance at 294EAA38 with private size 108 bytes at 294EAA80
[MIU][Utopia]: 
[MIU INFO] miu opencreate instance at 294EAAF0 with private size 80 bytes at 294EAB38
create instance at 294EAB90 with private size 48 bytes at 294EABD8

uboot held at [292DDF60~2AC00000],size=019220A0
CPU  : Messi
Board: BD_MST091B_10ASXG_15281_MESSI
DRAM:  172 MiB
Now running in RAM - U-Boot at: 29D00000

eMMC: HS200 200MHz 
eMMC 7.28 GB [E8FFF8h]

 UART BUS OFF!!

EMMC Информация :
EMMC CID: 90014A483847346192A18E82E0C537CF
EMMC CSD: D02701320F5903FFFFFFFFE78A40002B
EMMC Производитель : SKHYNIX , EMMC Имя: H8G4a , HEX: 483847346100 , S/N: 8E82E0C5 , rev. 0xA1
EMMC Производитель ID: 0x90 , OEM ID: 0x4A , Тип устройства: BGA (Discrete embedded) , Дата: 3/2020
   EMMC ROM 1 (Данные пользователя) Объем: 7456 MB (0001D2000000)
   EMMC ROM 2/3 (Загрузочный раздел 1/2) Объем: 4096 KB (000000400000)
   eMMC RPMB (защищенный блок данных): емкость: 4096 KB (000000400000) Counter: 110563 , Response: Not Clean
EMMC Постоянная защита записи: Нет
EMMC Временная защита записи: Нет
Extended CSD информация :
Extended CSD ревизия: 1.8 (MMC 5.1)
Конфигурация загрузки [PARTITION_CONFIG]: 0x00 , Загрузка из: нет загрузки
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n сигнал временно отключен
Поддержка управления разделами [PARTITIONING_SUPPORT]: 0x07
Устройство поддерживает функции разбиения
Устройство может иметь расширенные технологические возможности в разделах и области пользовательских данных
Устройство может иметь атрибуты расширенных разделов
Свойства раздела [PARTITION_SETTING_COMPLETED]: 0x00
Бэкап сохранён: H8G4a_8E82E0C5_20230802_131658.extcsd
EMMC Инициализация выполнена.

Предупреждение: Health report очень ПЛОХОЙ

Device Life Time Estimation (MLC) [269]: 0x0B   Exceeded its maximum estimated device life time
Device Life Time Estimation (SLC) [268]: 0x01   0% - 10% device life time used
Pre EOL information [267]: 0x03   Urgent

USB VCC: Chip VCC = 3,31
LibUSB ver 1.2.6.0
FileVersion = 0.2.21.35
Using:
1bit bus
Fast timing (16MHz)
Use Fixed Block operation
Using Ignore Errors
eMMC OCR 0xC0FF8080 after 2 attempts
CMD1 Get Response Error!
R3 Response Check Bits Error (0x19)!
eMMC (0) CID = 1501003847544634520641C6C05F35 (5F)
CMD2 Get Response Error!
Found 1 eMMC device(s)
eMMC CSD = D02701320F5903FFF6DBFFEF8E4040
eMMC: Version 4.xx
eMMC: Read Block Length 512 byte
eMMC: Write Block Length 512 byte
eMMC: Card High Capacity
eMMC: CSD User Partition Size = 1073741824 Byte
eMMC: WP Status True
eMMC: WP Size 16 erase groups
eMMC: Permanent WP is False
eMMC: Temorary WP is False
Valid mode SDR 1 bit
SET: Using HS Timing
eMMC: EXT_CSD User Partition Size = 7818182656 Byte
eMMC: Version 5.1
EXTCSD: FW CONFIG = 0x0
EXTCSD: PARTITION CONFIG = 0x8
EXTCSD: BOOT BUS WIDTH = 0x2
eMMC: Erase Group Size = 512 KByte (1024 blocks)
eMMC: Boot partition size 4194304 byte
eMMC: RPMB partition size 524288 byte
RPMB: Authentication key not yet programmed
eMMC MID = 0x0015, OEM ID = 0x0001
eMMC Product Name = 8GTF4R
eMMC Name = KLM8G1GETF-B041
eMMC Serial number = 0x41C6C05F
eMMC Revision = 0.6
eMMC Date 3/2002

10:28:22
Используем Boot1 раздел eMMC
10:30:08
Стирание Boot1 раздела начато
Стираем 8 блоков
ERASE: стираем по 16384 блоков
Стирание успешно !

10:30:08

Используем Boot1 раздел eMMC
Записываем файл E:\Прошивки\yf hfp,jh\телевизор\Dexp\DEXP F43D8000Q_CV338H-U42\DEXP F43D8000Q_CV338H-U42_MSD6A338SXG-ST_U9_KLM8G1GETF\eMMC\BOOT1_0x0000000000_0x0000400000_backup.boot1
Используем раздел Boot1
Запись начата
10:32:28
Записываем 8192 блок(ов) из доступных 8192
WRITE: записываем каждые 1024 сектора пакетом по x2(128) блоков
Успешно!
Запись завершена
10:32:32
Используем Boot2 раздел eMMC
10:32:39
Стирание Boot2 раздела начато
Стираем 8 блоков
ERASE: стираем по 16384 блоков
Стирание успешно !

10:32:39

Используем Boot2 раздел eMMC
Записываем файл E:\Прошивки\yf hfp,jh\телевизор\Dexp\DEXP F43D8000Q_CV338H-U42\DEXP F43D8000Q_CV338H-U42_MSD6A338SXG-ST_U9_KLM8G1GETF\eMMC\BOOT2_0x0000000000_0x0000400000_backup.boot2
Используем раздел Boot2
Запись начата
10:32:53
Записываем 8192 блок(ов) из доступных 8192
WRITE: записываем каждые 1024 сектора пакетом по x2(128) блоков
Успешно!
Запись завершена
10:32:58

Используем User раздел eMMC
10:33:05
Стирание User раздела начато
Стираем 14912 блоков
ERASE: стираем по 16384 блоков
Стирание успешно !

10:33:09

Используем User раздел eMMC
Записываем файл E:\Прошивки\yf hfp,jh\телевизор\Dexp\DEXP F43D8000Q_CV338H-U42\DEXP F43D8000Q_CV338H-U42_MSD6A338SXG-ST_U9_KLM8G1GETF\eMMC\USER_0x0000000000_0x01D2000000_backup.user
Используем раздел User
Запись начата
10:33:33
Записываем 15269888 блок(ов) из доступных 15269888
WRITE: записываем каждые 1024 сектора пакетом по x2(128) блоков
Error crc status 0xB
Ошибка записи блока 3825664, попытка 1
Error crc status 0xB
Ошибка записи блока 3903488, попытка 1
Успешно!
Запись завершена
12:53:41