Jump to content
Sign in to follow this  
Dadi

Philips 55PFS8159/12 - QV14.1E LA - Boot Loop

Recommended Posts

Posted (edited)

Привет.

 

телевизор Philips 55PFS8159/12

Panel: TPT550J1-HJ06 REV: SC1C
MainBoard: 715RLPCB0000000055

 

извините за мой язык. мой телевизор больше не работает. Кто-нибудь может мне помочь?

Вот выдержка из протокола:

 

Скрытый текст

 

----------------------------------------------------------------------------------------------------------------------------------------------------

 

[11.912805] TZ CPU0 ERROR[tz_sw_verify_image:75] verify image fail, src=0x19c00000, len=0x02738c00, dst=0x19c00000GIH magic num is not correct (0x482a4d49 != 0x00010080)!!!

recovery partition image is not proper !!!

****** BOOTLOADER_NORMAL_RESET_STAGE********

Send WARMUP_1_RESP.

Answering WU_FROM_DDR_OFF1.

[ 694618]I(SM): SM:Enter warmup state

[ 694622]I(SM): ******leave flow ---Sysreset to FastActive---

Send FAST RESET command to SM

[ 694821]W(SM): %%%%SM:Msg FAST SYSTEM RESET%%%%

[ 694825]I(SM): ******enter flow ---Sysreset to FastActive---

[ 694832]I(SM): peripheral_assert done

[ 694835]I(SM): soc_assert done

[ 694838]I(SM): mv_sm_power_socpoweroff done

[ 695143]I(SM): mv_sm_power_socpoweron done

[ 695203]I(SM): peripheral_assert done

[ 695207]I(SM): soc_assert done

[ 695303]I(SM): peripheral_deassert done

[ 695306]W(SM): ### Wake Up Reason 0x0[ 695310]I(SM): soc_deassert done

[ 695313]E(SM): mv_sm_timer_start - arg check fail!
/_S?àḞb[ 0] sys_init start. boot_strap=0x00000514 (source=eMMC), boot_state=0x7

image verify fail!!!

remote:ea84e1950f9bbe56d176bbfa1ae646ae5750a3cabda467c4b16bc4939c57926e

local :

tzk image verify fail.

[ 415] image verified, start at 0x00920000...

tz kernel starting... MV88DE3114(BG2Q)-A1 total 4 cpus, v2.0.0.21, Aug 5 2014 14:39:52

0213[ 471] start_bootloader

UẂULAUNCH_ITM is set to zero

board_number = 2

uiBoot = 7


I2C switch set as 0


I2C switch set as 1

--------- I2C Initialization ----------

I2C_INIT: I2C-2 bus

I2C_INIT: I2C-1 bus

I2C_INIT: I2C-0 bus

DDR reg 0xF7CB0BAC value : 0x00021421

DDR reg 0xF7CB0C00 value : 0x00004031

leakage info 400.

set Vcpu to 1300mV, default setting by hardware.

core from 1200 to 1150

set Vcore to 1175mv

set Vcore to 1150mv

set Vcore to 1150 mv.

SPLASH: wakeup_reason : 0

****** SPLASH ENABLED FOR Recovery********

flash_ts_init() success.


RDKDMP BG2Q [Oct 27 2017 18:04:12]

Pinmux configuration:


GSM 0xf7fcd040 0x009c0261;

0xf7ea0014: 00000072 00240611 00000253 1249008a

0xf7ea0028: 01249492 00000048 1ca54009 0430e44d

0xf7ea003c: 00000000 00000000 0000001f 63c06a52

Clock configuration:

VCO_B frequency 1620

AVPLLB[4] frequency 300

AVPLLB[5] frequency 800

AVPLLB[6] frequency 1680

AVPLLB[7] frequency 610

cpuPll frequency 1200

memPll frequency 1500

sysPll frequency 800

dClk frequency 375

cpuClk frequency 1200

sysClk frequency 400

drmClk frequency 400

cfgClk frequency 100

gfxClk frequency 400

zspClk frequency 400

perifClk frequency 200

pCubeClk frequency 610

vScopeClk frequency 610

nfcEccClk frequency 100

vppSysClk frequency 400

appClk frequency 800

gfx3DCoreClk frequency 420

gfx3DSysClk frequency 400

arcRefClk frequency 400

vipClk frequency 400

sdioXinClk frequency 200

sdio1XinClk frequency 200

gfx3DShClk frequency 420

avif0Clk frequency 300

avif1Clk frequency 300

[00,sd00] bootloader: part1(start=0, blks=1, version=201710271804), part2(start=0, blks=1, version=000000000000)

[01,sd01] fts: part1(start=32, blks=32, version=201710271804), part2(start=32, blks=32, version=000000000000)

[02,sd02] recovery: part1(start=64, blks=120, version=201710271804), part2(start=64, blks=120, version=000000000000)

[03,sd03] tzk_recovery: part1(start=184, blks=8, version=201710271804), part2(start=184, blks=8, version=000000000000)

[04,sd04] factory_setting: part1(start=192, blks=128, version=201710271804), part2(start=192, blks=128, version=000000000000)

[05,sd05] itm: part1(start=320, blks=128, version=201710271804), part2(start=320, blks=128, version=000000000000)

[06,sd06] boot: part1(start=448, blks=24, version=201710271804), part2(start=448, blks=24, version=000000000000)

[07,sd07] tzk_normal: part1(start=472, blks=8, version=201710271804), part2(start=472, blks=8, version=000000000000)

[08,sd08] system: part1(start=480, blks=1600, version=201710271804), part2(start=480, blks=1600, version=000000000000)

[09,sd09] user_setting: part1(start=2080, blks=960, version=201710271804), part2(start=2080, blks=960, version=000000000000)

[10,sd10] cache: part1(start=3040, blks=896, version=201710271804), part2(start=3040, blks=896, version=000000000000)

[11,sd11] firmware: part1(start=3936, blks=64, version=201710271804), part2(start=3936, blks=64, version=000000000000)

[12,sd12] factory_data: part1(start=4000, blks=32, version=201710271804), part2(start=4000, blks=32, version=000000000000)

[13,sd13] userdata: part1(start=4032, blks=3328, version=201710271804), part2(start=4032, blks=3328, version=000000000000)

get macaddr from fts: 1c:5a:6b:XX:XX:XX

macaddr=1c:5a:6b:XX:XX:XX

get_reset_msg,1262: sysreset, need to get reset_msg_extra_size=0

tzk boot with recovery mode

 

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

 

 

Затем перезагрузите снова.

У меня нет большого опыта. Теперь мне нужно починить чип eMMC с помощью программатора или его нужно заменить полностью?

 

Это не меню восстановления. Даже в сервисном меню с пультом. Обновление через USB тоже не работает.

Большое спасибо за вашу помощь.

 

Edited by Dadi

Share this post


Link to post
Share on other sites

@Dadi Для начала, нужно подключится к eMMC по ISP и считать её содержимое программатором. Снимать её не надо, от нагрева можно потерять данные в ней. Если они будут потеряны, придётся ставить новый main.

  • Спасибо 1

Share this post


Link to post
Share on other sites

Аналогичный телевизор. Считал eMMC - в ней много бед блоков.

Готов оплатить услуги тому кто сумеет восстановить дамп.

Share this post


Link to post
Share on other sites

@Coollio , открывайте свою тему в ЭТОМ разделе!

За мусор в чужой теме - ПРЕДУПРЕЖДЕНИЕ!

  • Положительно 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...

Important Information

Guidelines и Terms of Use Форума KenotronTV.RU