Jump to content

LED BQ 40S01B V1, TP.MT5510S.PB757 зависает на заставке Smart TV


Go to solution Solved by a.radzikhovskii,

Recommended Posts

BQ 40S01B V1

 

MAIN - TP.MT5510S.PB757

PANEL - C400Y19-C5

CPU - MT5659QHNT

eMMC - KLM8G1GETF

При вкл. тел. останавливается на заставке SMART TV,  после на пульт и кнопку вкл. не реагирует.

 лог вкл в сеть:

Hidden Content

    Reply to this topic to see the hidden content.

Пробовал через USB (fat32) загрузить allupgrade_5510_8G_1G_ref74.pkg , взятый 

Hidden Content

    Reply to this topic to see the hidden content.
.,  на экране Update firmware и через 2 минуты гаснет экран и выключается. Ничего не меняется. Возможно с файлом проблема? Или не подходит? Или имя другое надо (хотя процессc обновления стартует).

Хотелось бы слить родной с помощью rt809h, но нужны точки.

На форуме нашел это . (с точками прошу помощи)

На просторах нашел 

Hidden Content

    Reply to this topic to see the hidden content.

лог:

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

Link to post
Share on other sites
1 час назад, a.radzikhovskii сказал:

BQ 40S01B V1

 

MAIN - TP.MT5510S.PB757

PANEL - C400Y19-C5

CPU - MT5659QHNT

eMMC - KLM8G1GETF

При вкл. тел. останавливается на заставке SMART TV,  после на пульт и кнопку вкл. не реагирует.

 лог вкл в сеть:

  Показать контент

Boot-

EFUSE=3;

DRAM Channel A Calibration.

1T = (109 - 34) = 75 delay cells

Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell =15 ps 

Byte 0 : Gating(-25 ~ 25), Size=51 .

Byte 1 : Gating(-26 ~ 26), Size=53 .

Byte 2 : Gating(-26 ~ 26), Size=53 .

Byte 3 : Gating(-25 ~ 26), Size=52 .

HW Byte 0 : DQS(-14 ~ 13), Size 28 , Set 0. 

HW Byte 1 : DQS(-13 ~ 12), Size 26 , Set 0. 

HW Byte 2 : DQS(-11 ~ 10), Size 22 , Set 0. 

HW Byte 3 : DQS(-13 ~ 12), Size 26 , Set 0. 

DATLAT calibration 

first_step= 17 total pass= 6 best_step=19 .

TX HW Byte 0 : DQS(29 ~ 53), Size 25, Set 41. 

TX HW Byte 1 : DQS(27 ~ 50), Size 24, Set 38. 

TX HW Byte 2 : DQS(31 ~ 53), Size 23, Set 42. 

TX HW Byte 3 : DQS(33 ~ 54), Size 22, Set 43. 

DRAM A Size = 1024 Mbytes.

Boot


Start Pmain


EMMC boot

.

CID:0xdca166b7

:0x52069d1c

:0x47544634

:0x15010038

LZHS addr:0x00100040

LZHS size:0x000f2948

LZHS size:0x0005fafc

LZHS checksum:0x000000fe

LZHS begin 

LZHS ok

Boot


Start Lmain

 

MT5863 Boot Loader v0.9
MUSB_Init : ++
It has 2 USB Port,is 1, 1, 0, 0(1=using, 0=not use).
USB0: Set GPIO-1 = 1.
USB0: Set GPIO-1 error.
USB1: Set GPIO-1 = 1.
USB1: Set GPIO-1 error.
USB Port 0 is initial.
USB Port 1 is initial.
Set port-0 to Host mode.
Set port-1 to Host mode.
Support network![MSDC] LOADER FAST READ EMMC!
[MSDC] Init config, cid = 0x15010038, dsc=0xdca166b7, rca=0x52069d1c, ocr=0x47544634
[MSDC] loader RCA  1, 1 
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] MT22627:15010038:47544634:52069d1c:dca166b7
[MSDC] id1:00384754 id2:46345206
[MSDC] eMMC Name: UNKNOWN
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] Prepare set msdc  Bus Clock as HS25(MHz),src 12 ,mode 0, div 4 
[MSDC] Set Bus Clock as HS25(MHz) Success!,src 12 ,mode 0, div 4 
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863 
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] [eMMC2DRAM]enter into SDR50 Mode, max dtr 200000000 
[MSDC] Prepare set msdc  Bus Clock as HS0(MHz),src 0 ,mode 0, div 16 
[MSDC] Set Bus Clock as HS0(MHz) Success!,src 0 ,mode 0, div 16 
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863 
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 0 !
[MSDC] Prepare set msdc  Bus Clock as HS50(MHz),src 12 ,mode 0, div 2 
[MSDC] Set Bus Clock as HS50(MHz) Success!,src 12 ,mode 0, div 2 
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863 
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] 
Saved info: id1 = 0x66b75206, id2=0x9d1c4754,flag 0xaabbccdd,speedmode 5, dlycell 74 
[MSDC] Support HS400, card type ext_csd[196]0x57 
[MSDC] Support HS200, card type ext_csd[196]0x57 
[MSDC] u4mask = 0x3 
[MSDC] ID: 0x15010038, 0x47544634, 0x52069d1c, 0xdca166b7 
[MSDC] 
 Cur info: id1 = 0x66b75206, id2=0x9d1c4754,flag 0xaabbccdd,speedmode 5, dlycell 75 
[MSDC] 
-----The information is match, Alrady run autok before, ignore this time--
[MSDC] Load Param: 
[MSDC] K_IOCON: 0x200000a 
[MSDC] K_PAD_TUNE0: 0x2000 
[MSDC] K_PAD_TUNE1: 0x0 
[MSDC] K_PATCH_BIT0: 0x403c0006 
[MSDC] K_PATCH_BIT1: 0xfffe4309 
[MSDC] K_PATCH_BIT2: 0x448a1803 
[MSDC] K_EMMC50_CFG0: 0xe88832 
[MSDC] K_DAT_RD_DLY0: 0x4040504 
[MSDC] K_DAT_RD_DLY1: 0x3020404 
[MSDC] K_DAT_RD_DLY2: 0x0 
[MSDC] K_DAT_RD_DLY3: 0x0 
[MSDC] K_EMMC50_PAD_DS_TUNE: 0x11025 
[MSDC] K_EMMC50_PAD_CMD_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT01_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT23_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT45_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT67_TUNE: 0x0 
[MSDC] Current speed mode 1, clock 50.
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] --ENTER RPMB--
[MSDC] --EXIT RPMB--
[MSDC] Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell = 15 ps
[MSDC] TCMGET_DLYCELL_PERT = 75 
1st MAC in EEP is valid (c0:8a:cd:98:5e:3e)
Boot reason: A/C power on!!11111 u1AtmosEnable = 10
Remove Quiet Boot misc control in eeprom when Watchdog reason.

Normal zcc Start,using customer ir
IR DATA register : 0x       0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x  dbb538, size: 21076)success!!
T8032 FW version: 6
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x69f00 0x80


DTV>help

[Help]
upgrade(u):             Upgrade firmware
boot(bt):               Boot firmware
logo(logo):             Display logo
chipid(chipid):         print chip id
memtest:                Memory test
eeprom:                 Eeprom command
msdc:                   Msdc command
read(r):                Memory read(word)
write(w):               Memory write(word)
basic_(b):              basic command
mtktool(0):             mtktool command
cd:                     Change current directory
do:                     Repeat command

 

DTV>

 

Побывал через USB (fat32) загрузить allupgrade_5510_8G_1G_ref74.pkg , взятый 

Hidden Content

    Reply to this topic to see the hidden content.
.  на экране Update firmware и через 2 минуты гаснет экран и выключается. Ничего не меняется. возможно с файлом проблема? или не подходит? или имя другое надо (хотя процессc обновления стартует).

Хотелось бы слить родной с помощью rt809h, но нужны точки.

На форуме нашел это . (с точками прошу помощи)

На просторах нашел 

Hidden Content

    Reply to this topic to see the hidden content.

 

лог:

  Показать контент

Boot-

EFUSE=3;

DRAM Channel A Calibration.

1T = (108 - 34) = 74 delay cells

Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell =15 ps 

Byte 0 : Gating(-26 ~ 26), Size=53 .

Byte 1 : Gating(-25 ~ 26), Size=52 .

Byte 2 : Gating(-25 ~ 25), Size=51 .

Byte 3 : Gating(-25 ~ 25), Size=51 .

HW Byte 0 : DQS(-14 ~ 13), Size 28 , Set 0. 

HW Byte 1 : DQS(-13 ~ 12), Size 26 , Set 0. 

HW Byte 2 : DQS(-11 ~ 11), Size 23 , Set 0. 

HW Byte 3 : DQS(-13 ~ 13), Size 27 , Set 0. 

DATLAT calibration 

first_step= 17 total pass= 6 best_step=19 .

TX HW Byte 0 : DQS(28 ~ 52), Size 25, Set 39. 

TX HW Byte 1 : DQS(28 ~ 51), Size 24, Set 39. 

TX HW Byte 2 : DQS(31 ~ 53), Size 23, Set 42. 

TX HW Byte 3 : DQS(33 ~ 54), Size 22, Set 43. 

DRAM A Size = 1024 Mbytes.

Boot


Start Pmain


EMMC boot

.

CID:0xdca166b7

:0x52069d1c

:0x47544634

:0x15010038

LZHS addr:0x00100040

LZHS size:0x000f2948

LZHS size:0x0005fafc

LZHS checksum:0x000000fe

LZHS begin 

LZHS ok

Boot


Start Lmain

 

MT5863 Boot Loader v0.9
MUSB_Init : ++
It has 2 USB Port,is 1, 1, 0, 0(1=using, 0=not use).
USB0: Set GPIO-1 = 1.
USB0: Set GPIO-1 error.
USB1: Set GPIO-1 = 1.
USB1: Set GPIO-1 error.
USB Port 0 is initial.
USB Port 1 is initial.
Set port-0 to Host mode.
Set port-1 to Host mode.
Support network![MSDC] LOADER FAST READ EMMC!
[MSDC] Init config, cid = 0x15010038, dsc=0xdca166b7, rca=0x52069d1c, ocr=0x47544634
[MSDC] loader RCA  1, 1 
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] MT22627:15010038:47544634:52069d1c:dca166b7
[MSDC] id1:00384754 id2:46345206
[MSDC] eMMC Name: UNKNOWN
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] Prepare set msdc  Bus Clock as HS25(MHz),src 12 ,mode 0, div 4 
[MSDC] Set Bus Clock as HS25(MHz) Success!,src 12 ,mode 0, div 4 
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863 
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] [eMMC2DRAM]enter into SDR50 Mode, max dtr 200000000 
[MSDC] Prepare set msdc  Bus Clock as HS0(MHz),src 0 ,mode 0, div 16 
[MSDC] Set Bus Clock as HS0(MHz) Success!,src 0 ,mode 0, div 16 
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863 
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 0 !
[MSDC] Prepare set msdc  Bus Clock as HS50(MHz),src 12 ,mode 0, div 2 
[MSDC] Set Bus Clock as HS50(MHz) Success!,src 12 ,mode 0, div 2 
[MSDC] MsdcSmapleDelay: u4IC_Value = 0x5863 
[MSDC] Use NEW AutoK idea ,ignore the old ett param
[MSDC] Set pad driving as 5 !
[MSDC] 
Saved info: id1 = 0x66b75206, id2=0x9d1c4754,flag 0xaabbccdd,speedmode 5, dlycell 74 
[MSDC] Support HS400, card type ext_csd[196]0x57 
[MSDC] Support HS200, card type ext_csd[196]0x57 
[MSDC] u4mask = 0x3 
[MSDC] ID: 0x15010038, 0x47544634, 0x52069d1c, 0xdca166b7 
[MSDC] 
 Cur info: id1 = 0x66b75206, id2=0x9d1c4754,flag 0xaabbccdd,speedmode 5, dlycell 74 
[MSDC] 
-----The information is match, Alrady run autok before, ignore this time--
[MSDC] Load Param: 
[MSDC] K_IOCON: 0x200000Connect interrupt = 0x10, pBase = 0xf0051000.

[MSDC] K_PAD_TUNE0: 0x2000 
[MSDC] K_PAD_TUNE1: 0x0 
[MSDC] K_PATCH_BIT0: 0x403c0006 
[MSDC] K_PATCH_BIT1: 0xfffe4309 
[MSDC] K_PATCH_BIT2: 0x448a1803 
[MSDC] K_EMMC50_CFG0: 0xe88832 
[MSDC] K_DAT_RD_DLY0: 0x4040504 
[MSDC] K_DAT_RD_DLY1: 0x3020404 
[MSDC] K_DAT_RD_DLY2: 0x0 
[MSDC] K_DAT_RD_DLY3: 0x0 
[MSDC] K_EMMC50_PAD_DS_TUNE: 0x11025 
[MSDC] K_EMMC50_PAD_CMD_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT01_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT23_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT45_TUNE: 0x0 
[MSDC] K_EMMC50_PAD_DAT67_TUNE: 0x0 
[MSDC] Current speed mode 1, clock 50.
[MSDC] ---MSDC Set FIFO path and Init---
[MSDC] --ENTER RPMB--
[MSDC] --EXIT RPMB--
[MSDC] Clock frequency = 864 MHz, Clock period = 1157 ps, 1 delay cell = 15 ps
[MSDC] TCMGET_DLYCELL_PERT = 74 
1st MAC in EEP is valid (c0:8a:cd:98:5e:3e)
Boot reason: A/C power on!!11111 u1AtmosEnable = 10
Remove Quiet Boot misc control in eeprom when Watchdog reason.

Normal zcc Start,using customer ir
IR DATA register : 0x       0
T8032 init A/C on case loader stage...
Load T8032 FW (addr: 0x  dbb538, size: 21076)success!!
T8032 FW version: 6
T8032 change to loader stage...
LDR_FlashCopy 0xf010 0x69f00 0x80
<5507> getenv flag=0x1a01, len=0x0b
clean_all_AT_ENV
<5508> getenv flag=0x1a00, val=0xff
<5507> setenvbybuffer flag=0x1a01, len=0x07
<5508> setenv flag=0x1a0a, val=0xff
<5508> setenv flag=0x1a0b, val=0xff
<5508> setenv flag=0x375, val=0xff
[readRecoveryCmd] readRecoveryCmd start
recovery cmd:,para:

Do USB upgrade
u1USBBlock = 0x01d0a900
USB: Vbus turn up time = 339 ms, Max =1000 ms.
USB-1: insert.
Device High speed.
MGC_HostEnumerator:MGC_EnumStateGetMaxDevice
HubPort-0: Device reset.
Silent Reset: Root device = 0x01d0bb44, Reset.
MGC_HostEnumerator:MGC_EnumStateReset
HubPort-0: Device address = 1.
MGC_HostEnumerator:MGC_EnumStateSetAddress
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: idVendor = 0xabcd.
HubPort-0: idProduct = 0x1234.
HubPort-0: bcdDevice = 0x0100.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Lang Id: 0x409.
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Manufacturer: General .
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: Product: UDisk           .
MGC_HostEnumerator:MGC_EnumStateGetFullDevice
HubPort-0: SerialNum: 1312262021280468037501.
MGC_HostEnumerator:MGC_EnumStateSizeConfigs
MGC_HostEnumerator:MGC_EnumStateGetConfigs
MGC_HostEnumerator:MGC_EnumStateConnectDevice
USB Enumerator: find device driver
MGC_HostFindDriver:++
MUSB_TARGET_CLASS case 2:bMatch =1, 0x0,0x0
MUSB_TARGET_CLASS case1:bMatch =1,0x8,0x8
MUSB_TARGET_ACCEPT:bMatch = 1
HubPort-0: Driver support, class = 0x8.
USB Enumerator: Driver support
HubPort-0: Device is accepted.
HubPort-0: Device is accepted.
MGC_HostEnumerator:Connect device complete, bRet=1
MGC_HostEnumerator: break connect device
LUN = 0-1.
vid = 0xabcd, pid = 0x1234, bMediumStatus = 0.
USB-1: ClassCode= 0x8, u4Diff=0 ms.
MUSB_GetInsert return 1

 prLdrData->rDtvCfg.u1Upgrade_Ext :0x0 

 _fgDeviceType :0x0 

 FIND_CLASS_MASS_STORAGE.
Wait USB medium to be mounted...
LUN = 0-1.
ID = General UDisk           5.00. [RW].
Block size = 512 bytes, Total size = 3840 Mbytes.
MUSB_HfiMediumInserted().
USB Medium on Device, Time = 529 ms.
USB block size = 512 bytes.
/dev is created.
/mnt is already existed.  That is OK.
/dev/usb is created.
/mnt/usb_0 is created.
/dev/usb_0 is mounted as /mnt/usb_0.
<5507> clean_at_env for upgrade
<5508> getenv flag=0x1a00, val=0xff
<5508> setenv flag=0x1a00, val=0xff
<5508> setenv flag=0x375, val=0xff
<5508> setenv flag=0x1a0b, val=0xff
<5507> setenvbybuffer flag=0x1a01, len=0x0b
Upgrade File Name: allupgrade_5510_8G_1G_ref74.pkg
Upgrade File Size: 0x000000002f719390 Bytes
Display 0x00defc24 background:0x00000000
2 Find panel index 6(PANEL_CMO_37_H1) from EEPROM
PANEL_ReadSettingsFromEeprom u4ControlWord=0xffffffff, u1FacAtPanel=0xff, u1FacAtMap=0xff
before u4PanelControlWord = 0x00000029
LvdsDisplayBit = 0x00000020
IsLvdsOddSwOn = 0x00000000
IsLvdsMsbSwOn = 0x00000001
after u4PanelControlWord = 0x00000029
Curr panel controlword = 00000029
[SA7] _fgVopllUseDDDS = True
[LVDS] VOPLL Initialize successful !
LDR_OsdDisplay(13, 0x39108000, 816, 200)
Color:13 BmpAddr:0x39108000 Width:816 Height:200
===>plane2not flip any region===>plane3not flip any region===>plane1not flip any region[OSD]OSD_BASE_SetPlaneSwitchOrder: OSD plane order[3,2,1]
[OSD]OSD_BASE_UpdateAutoPosition: osd timing is from front scaler
[OSD]OSD_BASE_UpdateAutoPosition: HStart=357 VStart=10
upHaderAddr = 0x39888000, upDisAddr=0x39889000
Panel 1920 x 1080 

*************u4BmpPitch=1632******************
u4OutWidth=816,u4OutHeight=200,u4OutX=552,u4OutY=440.
[OSD]OSD_BASE_SetPlaneSwitchOrder: OSD plane order[3,2,1]
    #####_LdrDlmHandler =: /mnt/usb_0/allupgrade_5510_8G_1G_ref74.pkg
Msdc Erase Unit:0x100000
##########RSA public key######
73 3e 8d 9b 65 39 d7 aa 94 45 12 b1 c6 87 2e d2    s>..e9...E......
64 c2 93 76 0b 59 da bf be 16 b4 63 0e 09 1a 07    d..v.Y.....c....
23 b0 ..............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................New MTK Signature
b8 a7 df eb c5 eb 0f 69 36 7f d7 38 ae f6 a4 1f    .......i6..8....
d7 5e 6f 0c 31 ca 9d 15 4f f7 07 70 b7 26 ff 96    .^o.1...O..p.&..

MTK Signature matched

0x00000000 : 0x38, 0x47, 0x5f, 0x34, 0x35, 0x32, 0x39, 0x30,
0x00000008 : 0x35, 0x5f, 0x52, 0x45, 0x46, 0x37, 0x34, 0x5f,
0x00000010 : 0x32, 0x30, 0x31, 0x39, 0x30, 0x36, 0x31, 0x37,
0x00000018 : 0x5f, 0x31, 0x31, 0x34, 0x34, 0x33, 0x39, 0x00,
szCurVer=8G_452905_REF74_20190617_114439  CurVer =8G_452905_REF74_20190617_114439 
################### szUpgVer=(8G_452905_REF74_20190617_114439)  szCurVer=(8G_452905_REF74_20190617_114439) result = 0
########## ->upgrade NOT ALLOW
USB upgrade stop

LDR_EEPUserDrvCheckMagic u4HeaderData=0x17115253, u4Magic=0x17115253
<5508> getenv flag=0x1a09, val=0x00
<5508> LDR_IsGoBootup prLdrData->u4WakeupReason:6
<5508> getenv flag=0x1a08, val=0x00
<5508> setenv flag=0x1421, val=0xff
<5508> LDR_IsGoBootup AT_READ_FLAG=0, AT_B_FLAG=0
go to standby when ac on at factory mode 0.
RT710.dbg Loader_RT710_Standby
rt710.dbg ucI2cWrite_tuner OK
rt710.dbg ucI2cWrite_tuner OK
joe.dbg LDR I2C OK

 cvte R842 standby
qiujunshuai R842_Init
qiujunshuai R842_Standby
Servoadc Channel1 frist update!!!, value is 1023
Servoadc Channel1 finish update!!!, value is 1023

Normal zcc Start,using customer ir
Disable VGA wakeup
powerdown usb port2
support WOL                         
wol off, MAC register switch to arm

star:mtcmos poweroff eth
11111 u1AtmosEnable = 10
 loader The output gpio is 209  pfgSet0 
 loader The output gpio is 209  pfgSetis null 
Standby                         
PDWNC_EnterPowerDown(200100,6) 
SWITCH_T8032

 

Если Вы пробовали прошивку Телефункена то бесполезно т.к у Телефункена привязано все к серийнику

 

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

 

Link to post
Share on other sites
Posted (edited)
12 минут назад, rav2023 сказал:

Если Вы пробовали прошивку Телефункена то бесполезно т.к у Телефункена привязано все к серийнику

пробовал только allupgrade_5510_8G_1G_ref74.pkg. 

у Телефункена .bin .boot1 ... .part1 )

 

ребята если верить  - схема TP.MT5510S.PB803A 18097, как DO вычислить?

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

Edited by a.radzikhovskii
Link to post
Share on other sites
2 минуты назад, a.radzikhovskii сказал:

пробовал только allupgrade_5510_8G_1G_ref74.pkg. 

По вашей ссылке данная прошивка относится к вашей модели тв?

Link to post
Share on other sites

Вы проборвали переименовать файл? allupgrade_5510_sos.pkg

1 минуту назад, rav2023 сказал:

Вы проборвали переименовать файл? allupgrade_5510_sos.pkg

   вот тема прошлой недели изучите внимательно и не спеша

Edited by rav2023
Link to post
Share on other sites
20 часов назад, rav2023 сказал:

По вашей ссылке данная прошивка относится к вашей модели тв?

Если верить админу этого сайта, то да

 

 

20 часов назад, rav2023 сказал:

Вы проборвали переименовать файл? allupgrade_5510_sos.pkg

 попробую.

 

Link to post
Share on other sites

Я выкладывал здесь мануал как переименовывать tсли USB прошивка не идет или стоит на 1-10%

Можно фото шильдика TV?

Link to post
Share on other sites
  • Solution
Posted (edited)
19 часов назад, rav2023 сказал:

Нужно фото шильдика тв!

 С переименованием файла ...sos.pkg шьёт...уже мин 5. ( Сначала на экране отображалось upgrade...

Теперь BQ. и мигает светодиод синий/красный.)

 

Телевизор прошился.. с изменением имени файла. Спасибо.

Помогите с точками, сделаю DUMP////

Hidden Content

    Reply to this topic to see the hidden content.

Hidden Content

    Reply to this topic to see the hidden content.

Edited by a.radzikhovskii
  • Положительно 1
Link to post
Share on other sites

 

  • Отлично! 1

Поддержать KenotronTV - получить приглашение на форум!

Для наших зарубежных друзей,  возможный вариант пожертвования PayPal

 

Link to post
Share on other sites
Guest
This topic is now closed to further replies.
  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...